OS-49
2021-03-29 08:55 Click：times
The system isn't equipped with refrigeration dryer Specifications of Sullair Oil-water Separator
The system is equipped with refrigeration dryer
Correction on compressor relative humidity:
Level A Level B Level C
Turbine and without
additives
Diester, triester, PAG
Model m3 /min m3/min m3/min
OS-1 2.4 3 17
OS-16 3.8 3.2 26
OS-20 5.9 5 41
OS-33 12.4 10.5 85
OS-49 23 21 17.1
OS-94 33 28.1 22.8
OS-128 66.2 56 45.8
Level A Level B Level C
Turbine and without
additives Diester, triester, PAG
Model m3/min m3/min m3 /min
OS-1 1.8 1.5 1.2
OS-16 2.9 2.4 2
OS-20 4.4 3.8 3
OS-33 9.3 7.9 6.4
OS-49 18.5 15.8 12.8
OS-94 24.7 21 17
OS-128 49.5 41.6 34.2
Temperature ℉ 40℉ 50℉ 60℉ 70℉ 80℉ 90℉ 100℉ 110℉ 120℉
Temperature ℃ 4℃ 10℃ 16℃ 21℃ 27℃ 32℃ 38℃ 43℃ 49℃
Correction coefficient 2.82 1.96 1.39 1.00 0.73 0.54 0.40 0.31 0.22
RH 50% 55% 60% 65% 70% 75% 80% 85% 90% 95% 100%
Correction coefficient 1.30 1.18 1.08 1.00 0.93 0.87 0.81 0.76 0.72 0.68 0.65
Model OS-1 OS-16 OS-20 OS-33 OS-49 OS-94 OS-128
Dimension of inlet
- in(mm) 3/4”(19) 3/4”(19) 3/4”(19) 1”(25) 1”(25) 1”(25) 1”(25)
Dimension of outlet
- in(mm) 3/4”(19) 1”(25) 3/4”(19) 1”(25) 1”(25) 1”(25) 1”(25)
Volume of settling
chamber - gal(l) N/A 16(50) 20(75) 33(125) 49(185) 94(355) 128(485)
232(16) 232(16) 232(16) 232(16) 232(16) 232(16) 232(16)
41(5) 41(5) 41(5) 41(5) 41(5) 41(5) 41(5)
95(35) 95(35) 95(35) 95(35) 95(35) 95(35) 95(35)
Martial (recoverable) Polyethylene Polyethylene Polyethylene Polyethylene Polyethylene Polyethylene Polyethylene
Net weigh - lbs (kg) 13(6) 22(10) 26(12) 59(27) 79(36) 154(70) 214(97)
Total weight - lbs (kg) 54(24.5) 172.7(78.5) 206(93.5) 350(159) 477(217) 880(400) 1210(550)
Length “A” - in(mm) 12.4(316) 14.0(350) 14.0(350) 26.0(650) 26.0(650) 34.0(850) 34.0(850)
Width “B” - in(mm) 10.6(270) 17.0(433) 18.0(450) 20.0(500) 26.0(650) 28.0(700) 39.0(1000)
Height “C” - in(mm) 33.0(842) 32.0(810) 32.0(810) 47.0(1195) 47.0(1195)60.0(1535) 60.0(1635)
Mineral oil, PAO, TMP, PE, SRF
1/4000, SRF 11/8000, 24 KT
Max. pressure - psig(barg)
Min. temperature - F (℃)
Max. temperature - F (℃)
Mineral oil, PAO, TMP, PE, SRF
1/4000, SRF 11/8000, 24 KT
Standard conditions requirement of system:
Type of compressor: screw or sliding-vane-type*
Air inlet chamber ambient temperature: 70℉ (21℃)
Relative humidity: 65%
Air discharge temperature of compressor: 95℉ (35℃)
Dew point of refrigeration dryer (if installed): 38℉ (2℃)
(Where different from environment conditions described above, such as environmental temperature is too
high, please consider the influence factors such as temperature correction coefficient, you can also consult
Sulliar)
* If using the piston compressor, you can consult Sullair.
This model selection table is prepared based on the environment of air inlet chamber ambient temperature:
70℉ (21℃), Relative humidity: 65%. If the actual environment is inconformity with environment described
above, please select model based on the correction coefficient listed in the correction coefficient form
followed.
Note: Sullair keeps improving continuously, some performance and specification may be changed without
prior notice, Details please consult local Sullair representative or authorized agent.
Model:OS-1 Model:OS-16 to OS-128
Correction on compressor air inlet temperature F
TAG：